SHINOHARA ELECTRIC Supports isolés

?* À propos du délai d'expédition et des prix

• 

  Support PP, type G【25-50 pièces par conditionnement】

  SHINOHARA ELECTRIC

  Can be used to maintain insulation wiring within a high-pressure device. Secured using a cable tie.
  
  [Features]
  · Possible to easily and firmly maintain wiring via tightening with a cable band.
  · A total of three different types of varying heights are available for use with your preferred application.
  · Has excellent insulating properties, is lightweight, and won’t crack.

  Fichiers CAD 2D disponibles

  à partir de∗ ：	65.36 €
  Délai d'expédition minimum ：	7 jours

  *Prix unitaire/configuration de base

• 

  Taquet FRP

  SHINOHARA ELECTRIC

  Please use as a mother wire support mount. Made by FRP
  
  [Features]
  ・FRP materials are used as the machining material for a light weight.
  ・Does not rust.
  ・Strong
  ・Good insulation.
  · Machining can easily be performed.
  ・Good resistance to water absorption.
  · Has superior arc resistance.
  ・There is no need for post-machining treatment like with Bakelite.

  Fichiers CAD 2D disponibles

  à partir de∗ ：	26.60 €
  Délai d'expédition minimum ：	7 jours

  *Prix unitaire/configuration de base

• 

  Support de barre【50-100 pièces par conditionnement】

  SHINOHARA ELECTRIC

  Use the bus bar to support insulation.
  
  [Features]
  · The copper band and bar holder S are secured and tightened with a mounting bolt for a wide range of band thicknesses.
  · Reduced manual work compared to conventional insulation materials.
  · Copper bands can be mounted from both surfaces in a row by inserting the separator into the interstitial space.

  Fichiers CAD 2D disponibles

  à partir de∗ ：	321.05 €
  Délai d'expédition minimum ：	5 jours

  *Prix unitaire/configuration de base

• 

  Isolant résine【50 pièces par conditionnement】

  SHINOHARA ELECTRIC

  A high-pressure insulating support.
  
  [Features]
  · Smaller and lighter than conventional porcelain insulators, with excellent durability. Useful for streamlining.
  Features excellent electrical and mechanical properties.
  · Produced in accordance with JIS standards (JIS-C3851).

  Fichiers CAD 2D disponibles

  à partir de∗ ：	688.23 €
  Délai d'expédition minimum ：	5 jours

  *Prix unitaire/configuration de base

• 

  Base de support à trois étages【1-25 pièces par conditionnement】

  SHINOHARA ELECTRIC

  Can be used as a bus support base. Achieves space savings with three-stage design.
  
  [Features]
  · Can easily support a copper band by simple insertion of square nut(s).
  · Resin molding ensures that the product is lightweight and will not crack.

  Fichiers CAD 2D disponibles

  à partir de∗ ：	10.54 €
  Délai d'expédition minimum ：	5 jours

  *Prix unitaire/configuration de base

• 

  Base de support de bus de raccordement

  SHINOHARA ELECTRIC

  Use to support bus lines
  
  [Features]
  · No need to manually treat insulation like before.
  · Made of lightweight, non-breakable plastic.
  · Excellent insulation (for low voltages)

  Fichiers CAD 2D disponibles

  à partir de∗ ：	3.42 €
  Délai d'expédition minimum ：	5 jours

  *Prix unitaire/configuration de base

• 

  Support de montage pour isolant de support intérieur

  SHINOHARA ELECTRIC

  Can be used as a mounting bracket for indoor support insulators used in bus bars and wires.
  
  [Features]
  - A wide array of different sizes designed to match various mounting hole pitches used for indoor support insulators are available.
  - Different models can be selected based on the intended application, such as a clamp for round wires (high pressure covered wires) or a clamp for bus bar use (vertical support/horizontal support).

  Fichiers CAD 2D disponibles

  à partir de∗ ：	9.65 €
  Délai d'expédition minimum ：	8 jours

  *Prix unitaire/configuration de base

• 

  Supports EP【80-100 pièces par conditionnement】

  SHINOHARA ELECTRIC

  Use the emergency power holders for retaining the insulated wires on the inside of high-voltage equipment. This type of holder is secured by bolts on both sides.
  
  [Features]
  · This product has been manufactured based on the criteria that have been established in the guidelines for certification of electrical equipment receiving cubicle-type, dedicated, emergency power supply, enacted by the Japan Electric Association.
  · By using the adapters, wires of 5.5–250 ksi can be fully secured.
  · Excellent insulating properties (creepage plugs-circuit voltage of 22 kV or more), is lightweight, and will not crack.

  Fichiers CAD 2D disponibles

  à partir de∗ ：	42.76 €
  Délai d'expédition minimum ：	8 jours

  *Prix unitaire/configuration de base

• 

  Supports EI

  SHINOHARA ELECTRIC

  Use the EI supporters to support the conductors on the inside of low-voltage equipment. The supporters are manufactured from epoxy resin.
  
  [Features]
  · The load-bearing capacity is superior to that of conventional supporters. Therefore, the scope of application has been expanded further.
  · Has excellent insulating properties, is lightweight, and won’t crack.

  Fichiers CAD 2D disponibles

  à partir de∗ ：	4.37 €
  Délai d'expédition minimum ：	Jour même

  *Prix unitaire/configuration de base

• 

  Supports PP【100 pièces par conditionnement】

  SHINOHARA ELECTRIC

  Use the PP holders for retaining insulated wires on the inside of high-voltage equipment.
  
  [Features]
  · The PP holders can fully secure wires by tightening a single screw due to their hinged opening and closing type clamp covers.
  · By using the adapters, wires of various sizes can be fully protected and supported.
  · Has excellent insulating properties (creepage plugs-circuit voltage of 22 kV or more), is lightweight, and won’t crack.

  Fichiers CAD 2D disponibles

  à partir de∗ ：	34.50 €
  Délai d'expédition minimum ：	5 jours

  *Prix unitaire/configuration de base

• 

  Support de câble WS

  SHINOHARA ELECTRIC

  Use as a wire support base
  
  [Features]
  · Three types, from WS-1 to WS-3. Combine WS-1 with WS-2 to support a wide variety of electrical lines

  Fichiers CAD 2D disponibles

  à partir de∗ ：	1.70 €
  Délai d'expédition minimum ：	8 jours

  *Prix unitaire/configuration de base

• 

  Montage à taquet ajouré

  SHINOHARA ELECTRIC

  Use the free cleat mount for damping wire vibrations.
  
  [Features]
  · Holes have been drilled into the extruded resin material at 20 mm intervals.
  · Cables can be simply supported at intermediate locations by using zip ties.

  Fichiers CAD 2D disponibles

  à partir de∗ ：	14.43 €
  Délai d'expédition minimum ：	9 jours

  *Prix unitaire/configuration de base

• 

  Montage de support à 20 étages【25 pièces par conditionnement】

  SHINOHARA ELECTRIC

  Please use as an ELB ground support mount.
  
  [Features]
  ・By arranging copper bus bars on 2 vertical levels, particularly when ELB and general purpose ground bars need to be distinguished, this product can be used in the ELB vicinity within a small space so as to install 2 ground bars.

  Fichiers CAD 2D disponibles

  à partir de∗ ：	115.00 €
  Délai d'expédition minimum ：	8 jours

  *Prix unitaire/configuration de base

• 

  Base de support de bus inclinée【1-10 pièces par conditionnement】

  SHINOHARA ELECTRIC

  Can be used as a bus support base (sloped bus support base)
  
  [Features]
  · The sloped bus makes wire connection work easy.
  · Allows for a reduction in mounting space.

  • Remise sur volume

  Fichiers CAD 2D disponibles

  à partir de∗ ：	3.42 €
  Délai d'expédition minimum ：	Jour même

  *Prix unitaire/configuration de base

• 

  Supports de barres de bus【20 pièces par conditionnement】

  SHINOHARA ELECTRIC

  Use the polycarbonate bus bar supporters as supports for bus bars.
  
  [Features]
  · Copper strips can be supported by simply sandwiching the tops and bottoms of the strips.

  Fichiers CAD 2D disponibles

  à partir de∗ ：	164.10 €
  Délai d'expédition minimum ：	7 jours

  *Prix unitaire/configuration de base

• 

  Manchon isolant【100 pièces par conditionnement】

  SHINOHARA ELECTRIC

  Use for floating insulation in sequencers, etc.
  
  [Features]
  · The bushings are provided in male and female sets. The base units of equipment can be securely insulated by the method written below.
  · The bushings can be used with M4, M5, M6, M8, M10, and M12 bolts.

  Fichiers CAD 2D disponibles

  à partir de∗ ：	57.70 €
  Délai d'expédition minimum ：	5 jours

  *Prix unitaire/configuration de base

Loading...