SURUGA SEIKI Supports pour éléments optiques

?* À propos du délai d'expédition et des prix

• 

  Support de miroir, modèle compact (avec verrouillage)

  SURUGA SEIKI

  [Features]
  · A holder for holding small mirrors up to ø30 mm. The tilt (θy, θz) can be adjusted in the two axes.
  · Adhesive type and three-point support type fixing are available for the mirror fixing methods.
  · With the rod-less type, M3 or M6 screws are used for fixing.
  · With the three-point support type (F58N-30-2), mirrors from ø20 to 30 mm can be held by changing the position of the lower supporting pin.
  · The fine tilt-adjustment knob is P = 0.5 mm and can be fixed to a set incline with a lock nut.

  Fichiers CAD 2D / 3D disponibles

  à partir de∗ ：	108.53 €
  Délai d'expédition minimum ：	5 jours

  *Prix unitaire/configuration de base

• 

  Porte-lentille à 3 axes

  SURUGA SEIKI

  [Features]
  · The B11-40C is employed for the X-axis while the optical axis is configured at 45 mm.
  · Replace the lens and/or adapter to allow for use in different types of application.

  Fichiers CAD 2D / 3D disponibles

  à partir de∗ ：	558.28 €
  Délai d'expédition minimum ：	5 jours

  *Prix unitaire/configuration de base

• 

  Porte-lentille à 5 axes

  SURUGA SEIKI

  Replace the lens and/or adapter to allow for use in different types of application. Note: The CAD data for this series is being modified. This data will be made available as soon as the modifications have been completed.

  Fichiers CAD 2D / 3D disponibles

  à partir de∗ ：	675.51 €
  Délai d'expédition minimum ：	10 jours

  *Prix unitaire/configuration de base

• 

  Support LD

  SURUGA SEIKI

  F511L: fixed type. F512L, F513L: YZ axis adjustable LD holder. Select according to the number of pins and the pin pitch (pin P.C.D.) of the LD.

  Fichiers CAD 2D / 3D disponibles

  à partir de∗ ：	115.95 €
  Délai d'expédition minimum ：	10 jours

  *Prix unitaire/configuration de base

• 

  Supports LD (modèle de porte-puce)

  SURUGA SEIKI

  [Features]
  · A Chip Carrier type LD holder with a built-in Peltier element.
  · Features a built-in Peltier element, and a calibrated 10kΩ thermistor sensor.
  · The switching for the anode/cathode of the LD can be configured by replacing the jumper pins.
  · There are two types of Chip Carrier LD holder. Configure according to the mounting (output) direction of the LD.
  · For connectors, a D-sub9 pin female is used for driving the LD, and a D-sub9 pin male is used for the temperature controller.
  · The F129-1 water cooling adapter is also available.
  · Use a low temperature circulating water tank or similar to enable greater stabilization and for even lower temperatures.

  Fichiers CAD 2D / 3D disponibles

  à partir de∗ ：	629.95 €
  Délai d'expédition minimum ：	11 jours

  *Prix unitaire/configuration de base

• 

  Support LD (Modèle pour paquet)

  SURUGA SEIKI

  [Features]
  · A To-Package type LD holder with a built-in Peltier element.
  · Features a built-in Peltier element, and a calibrated 10kΩ thermistor sensor.
  · Supports LD sizes of ø5.6 (Pin PCD, 2.0) and ø9.0 (Pin PCD, 2.54) for three-pins and for four-pins respectively.
  · For common anodes and common cathodes, etc., configure by replacing the jumper pins.
  · For connectors, a D-sub9 pin female is used for driving the LD, and a D-sub9 pin male is used for the temperature controller.
  · The F129-1 water cooling adapter is also available.
  · Use a low temperature circulating water tank or similar to enable greater stabilization and for even lower temperatures.

  Fichiers CAD 2D / 3D disponibles

  à partir de∗ ：	629.95 €
  Délai d'expédition minimum ：	9 jours

  *Prix unitaire/configuration de base

• 

  Bague à vis

  SURUGA SEIKI

  A threaded ring for fixing lenses and mirrors. Note that even when the diameters are the same, the shapes can differ depending on the product. Note: The CAD data for this series is being modified. This data will be made available as soon as the modifications have been completed.

  • Remise sur volume

  Fichiers CAD 2D / 3D disponibles

  à partir de∗ ：	8.95 €
  Délai d'expédition minimum ：	Jour même

  *Prix unitaire/configuration de base

• 

  Adaptateurs isolants

  SURUGA SEIKI

  Can be used for optical system constructions. Note: The CAD data for this series is being modified. This data will be made available as soon as the modifications have been completed.

  à partir de∗ ：	141.61 €
  Délai d'expédition minimum ：	10 jours

  *Prix unitaire/configuration de base

• 

  Fixations inclinables de polariseur

  SURUGA SEIKI

  A holder that can retain items such as polarizing plates and wave plates. It can also rotate (θx) and tilt them (θy, θz). Note: The CAD data for this series is being modified. This data will be made available as soon as the modifications have been completed.

  Fichiers CAD 2D / 3D disponibles

  à partir de∗ ：	542.70 €
  Délai d'expédition minimum ：	11 jours

  *Prix unitaire/configuration de base

• 

  Cible d'alignement

  SURUGA SEIKI

  Can be used for optical system constructions.
  
  [Features]
  · Used for adjusting the optical axis when building an optical system for the Opt Station.
  · Push-down the large target-fixing pin to fix to the tapped hole on the plate board.
  · Return the pin upward to install in any position.
  · The mark on the target is adjusted to a height of 45 mm.
  · Target stickers (black cross on a white base / white cross on a black base) are included.

  Fichiers CAD 2D / 3D disponibles

  à partir de∗ ：	128.74 €
  Délai d'expédition minimum ：	10 jours

  *Prix unitaire/configuration de base

• 

  Accessoires pour tables à montages multiples - Adaptateur pour appareil photo CCS

  SURUGA SEIKI

  A holder for fixing cameras, CCD cameras, and vidicon cameras, etc. Note: The CAD data for this series is being modified. This data will be made available as soon as the modifications have been completed.

  Fichiers CAD 2D / 3D disponibles

  à partir de∗ ：	109.88 €
  Délai d'expédition minimum ：	5 jours

  *Prix unitaire/configuration de base

• 

  Adaptateur pour connecteur

  SURUGA SEIKI

  [Features]
  · An adapter for optical fiber connectors.
  · An FC type receptacle is included as standard, so please select according to the connector.
  · The FC type receptacle is designed so that when a connector is inserted, the end surface of the ferrule extends about 0.5 mm from the receptacle surface. Ideal for placing in close proximity to other items.

  Fichiers CAD 2D / 3D disponibles

  à partir de∗ ：	101.65 €
  Délai d'expédition minimum ：	5 jours

  *Prix unitaire/configuration de base

• 

  Adaptateurs pour lentille collimatée

  SURUGA SEIKI

  An adapter for holding ø4 to ø14.5 mm cylindrical items such as collimating lenses, etc. Used by attaching to various types of cross motion holder. Note: The CAD data for this series is being modified. This data will be made available as soon as the modifications have been completed.

  à partir de∗ ：	58.01 €
  Délai d'expédition minimum ：	10 jours

  *Prix unitaire/configuration de base

• 

  Supports de miroir Gimbaled

  SURUGA SEIKI

  A holder for fixing items such as mirrors or plate beam splitters etc. The tilt can be adjusted in the two axial directions. The center of rotation and the center of the mirror always coincide when making fine adjustments.
  
  [Features]
  ■ F50, F55
  · Holders for fixing mirrors, plate beam splitters, and lenses, etc. The tilt (θy, θz) can be finely adjusted.
  · Fine movement of ±4° to 6° is possible, in both θy and θz, by tightening the clamp. Loosening the clamp, allows for coarse movement (adjustment) over 360°.
  · A gimbal structure in which the center of rotation and the center of the mirror always coincide when making fine or coarse adjustments.
  · The included standard rod is ø 20, and has a length of 60 mm. However the rod length can be changed. The holder's screw holes are M6P = 1. A40 to A42 rods can be used.
  · Mirror Holder F50: For the feeding method, A-type micrometer heads and an E-type screw system are available.
  · Horizontally operated type mirror holder F55: Due to the unique horizontal operation method (the operation system is installed in a horizontal direction), the user can operate it without going in front of the optical axis with their hands. A proximity specification is also available.
  ■ F52
  · A holder for fixing mirrors, plate beam splitters, and lenses, etc. The tilt (θy, θz) can be finely adjusted in the two axial directions.
  · The tilt (θy, θz) of the two axes can be finely adjusted by ±2° or ±3° (F52).
  · A gimbal structure in which the center of rotation and the center of the mirror always coincide when making fine or coarse adjustments.
  · Items such as mirrors are attached and removed using a threaded ring. Includes a resin protective ring.

  Fichiers CAD 2D / 3D disponibles

  à partir de∗ ：	199.99 €
  Délai d'expédition minimum ：	10 jours

  *Prix unitaire/configuration de base

• 

  Porte-lentilles coulissant

  SURUGA SEIKI

  [Features]
  · Used for fixing round/square lenses or cylindrical/rectangular items of any size.
  · The attachment and detachment of elements is done by loosening the slide-clamp screw on the side surface, adjusting the position and, after fixing the screws, fixing the element using the clamp screw on the top.
  · The F44 can hold cylindrical elements such as lenses, while the F45 is suitable for fixing rectangular elements such as cylindrical lenses.

  Fichiers CAD 2D / 3D disponibles

  à partir de∗ ：	104.36 €
  Délai d'expédition minimum ：	5 jours

  *Prix unitaire/configuration de base

• 

  Adaptateur pour lentille SELFOC

  SURUGA SEIKI

  An adapter for holding cylindrical items. Used by setting on to fixed type holders and various types of cross motion holder. Note: The CAD data for this series is being modified. This data will be made available as soon as the modifications have been completed.

  Fichiers CAD 2D / 3D disponibles

  à partir de∗ ：	107.97 €
  Délai d'expédition minimum ：	10 jours

  *Prix unitaire/configuration de base

• 

  Supports de capteur / laser

  SURUGA SEIKI

  [Features]
  · Can adjust the tilt angle of small sensors and laser pointers.
  · P.C.D.32 tapped holes are included on the holder surface. Uses these to mount various types of adapter plate.

  Fichiers CAD 2D / 3D disponibles

  à partir de∗ ：	135.13 €
  Délai d'expédition minimum ：	10 jours

  *Prix unitaire/configuration de base

• 

  Adaptateur de capteur

  SURUGA SEIKI

  [Features]
  · An adapter for holding round sensors and lasers.
  · The adapter thickness has been set to 12 mm, increasing the holding force.
  · Specify the ø diameter when ordering.

  à partir de∗ ：	64.60 €
  Délai d'expédition minimum ：	10 jours

  *Prix unitaire/configuration de base

• 

  Support de wattmètre

  SURUGA SEIKI

  [Features]
  · A holder for fixing commercially available power meter sensors.
  · Mainly for fixing rectangular power meter sensors. Constructed so that the sensor will not shift, even when the sensor cable is pulled.
  · Fixing is done using a method of sandwiching with screws from the top.
  · Sensors that can be fixed are of limited availability.
  · Can be directly mounted onto bases with the rods removed.

  Fichiers CAD 2D / 3D disponibles

  à partir de∗ ：	130.83 €
  Délai d'expédition minimum ：	5 jours

  *Prix unitaire/configuration de base

• 

  Supports directionnels de faisceau

  SURUGA SEIKI

  [Features]
  · Types in which only the upper mirror is movable and types in which both the upper and lower mirrors are movable are available.
  · The pitch of the adjustment screw can be selected from 0.5 mm and 0.25 mm.
  · Adhesive fixing and three-point support fixing types are available for the mirror.
  · The lower side of the pole is an M16P (= 1 mm) male screw.
  · Can be fixed to magnetic bases and plates, etc.

  Fichiers CAD 2D / 3D disponibles

  à partir de∗ ：	285.26 €
  Délai d'expédition minimum ：	9 jours

  *Prix unitaire/configuration de base

• 

  Support de trou d'épingle

  SURUGA SEIKI

  [Features]
  · Capable of fixing pinholes and moving them in micro-movement increments in the YZ axis direction.
  · Pin holes with an external diameter of ø16 mm can be used.
  · Fix pin holes with an M20P = 0.5 threaded ring.
  · The optical axis central height is standardized at 25 mm from the bottom.

  Fichiers CAD 2D / 3D disponibles

  à partir de∗ ：	377.86 €
  Délai d'expédition minimum ：	10 jours

  *Prix unitaire/configuration de base

• 

  Adaptateur pour trou d'épingle

  SURUGA SEIKI

  Used by attaching to various types of cross motion holder. The applicable diameter of the pin hole is ø16 mm. Attachment and detachment is carried out using a threaded ring system. Note: The CAD data for this series is being modified. This data will be made available as soon as the modifications have been completed.

  Fichiers CAD 2D / 3D disponibles

  à partir de∗ ：	51.59 €
  Délai d'expédition minimum ：	10 jours

  *Prix unitaire/configuration de base

• 

  Virole d'adaptation

  SURUGA SEIKI

  An adapter for holding ferrules. Can hold fibers with not only ferrules but also those with SELFOC lenses, etc. Note: The CAD data for this series is being modified. This data will be made available as soon as the modifications have been completed.

  Fichiers CAD 2D disponibles

  à partir de∗ ：	77.30 €
  Délai d'expédition minimum ：	10 jours

  *Prix unitaire/configuration de base

• 

  Supports de prisme

  SURUGA SEIKI

  [Features]
  · Configured so that the optical axis height is at the center of the element when the element is 20 mm, and standardized at 25 mm from the bottom.
  · Move the upper sliding part to fix the prism.
  · Use the upper knob to fix without having to move the element.
  · The F551-20 bottom plate features M4 tapped holes. Mount a rod to change to a rod type.
  · F552-20 can be finely adjusted.
  · The elements are positioned using the pins in the three locations.

  Fichiers CAD 2D / 3D disponibles

  à partir de∗ ：	103.31 €
  Délai d'expédition minimum ：	5 jours

  *Prix unitaire/configuration de base

• 

  Tige avec plaque

  SURUGA SEIKI

  [Features]
  · Can be fitted with 40 mm stages and holders for Opt Stations, etc.
  · Can be arranged as needed and mounted to cross clamps, etc.

  Fichiers CAD 2D / 3D disponibles

  à partir de∗ ：	48.56 €
  Délai d'expédition minimum ：	9 jours

  *Prix unitaire/configuration de base

• 

  Supports de miroir

  SURUGA SEIKI

  An affordable mirror holder for fixing items such as mirrors or plate beam splitters. The tilt can be finely adjusted in the two axial directions. Note: The CAD data for this series is being modified. This data will be made available as soon as the modifications have been completed.

  Fichiers CAD 2D / 3D disponibles

  à partir de∗ ：	118.35 €
  Délai d'expédition minimum ：	6 jours

  *Prix unitaire/configuration de base

• 

  Supports de miroir (bande de fixation)

  SURUGA SEIKI

  A mirror holder with a slit-clamp type lock. Note: The CAD data for this series is being modified. This data will be made available as soon as the modifications have been completed.

  Fichiers CAD 2D / 3D disponibles

  à partir de∗ ：	144.27 €
  Délai d'expédition minimum ：	10 jours

  *Prix unitaire/configuration de base

• 

  Supports de miroir (axe optique : 25mm)

  SURUGA SEIKI

  A mirror holder with an optical axis height of 25 mm. For use with the Opt Station. Select the most appropriate mounting method so that the held element does not distort when mounted. Note: The CAD data for this series is being modified. This data will be made available as soon as the modifications have been completed.

  Fichiers CAD 2D / 3D disponibles

  à partir de∗ ：	108.12 €
  Délai d'expédition minimum ：	5 jours

  *Prix unitaire/configuration de base

• 

  Clé polygonale

  SURUGA SEIKI

  A ring wrench for tightening threaded rings. Variable types and fixed types are available in sizes to fit different ring diameters. Note: The CAD data for this series is being modified. This data will be made available as soon as the modifications have been completed.

  Fichiers CAD 2D disponibles

  à partir de∗ ：	82.01 €
  Délai d'expédition minimum ：	10 jours

  *Prix unitaire/configuration de base

• 

  Porte-lentilles

  SURUGA SEIKI

  Used for fixing circular items such as lenses, mirrors, and filters etc. Note: The CAD data for this series is being modified. This data will be made available as soon as the modifications have been completed.

  Fichiers CAD 2D / 3D disponibles

  à partir de∗ ：	49.38 €
  Délai d'expédition minimum ：	5 jours

  *Prix unitaire/configuration de base

• 

  Adaptateur pour lentille

  SURUGA SEIKI

  An adapter for lenses with an outer diameter of ø10 mm, ø12.7 mm, ø15 mm, ø20 mm, and ø25.4 mm. Used by attaching to various types o cross motion holder.
  
  [Features]
  · Used by attaching to various types of cross motion holder. Various types of single lens.
  · Lens attachment and detachment is carried out using a threaded ring system.
  Note: Includes threaded rings and resin rings.
  Note: A ring wrench for tightening threaded rings.

  Fichiers CAD 2D / 3D disponibles

  à partir de∗ ：	50.90 €
  Délai d'expédition minimum ：	5 jours

  *Prix unitaire/configuration de base

• 

  Supports de miroir commandés de dessus

  SURUGA SEIKI

  A top operated mirror holder with excellent stability and operability. Note: The CAD data for this series is being modified. This data will be made available as soon as the modifications have been completed.

  Fichiers CAD 2D / 3D disponibles

  à partir de∗ ：	216.50 €
  Délai d'expédition minimum ：	10 jours

  *Prix unitaire/configuration de base

• 

  Support à laser rond

  SURUGA SEIKI

  [Features]
  · F20 sandwiches the laser between three screws. The optical axis is adjusted by screwing in and out.
  · With F21, in addition to the function of F20, it is possible to adjust in the θy direction by operating the screw at the bottom of the holder.
  · Both F20 and F21 have two types, L=150 and 250, depending on the length of the laser.
  · The included standard rod has a diameter of ø20 and a length of 60, but both the rod diameter and length can be changed upon request.
  · The laser holding part can be fixed to positions at 50 mm intervals by removing the fixing screw from the bottom (only F20-150/250).
  · The F20 can be attached directly to the breadboard (A65) by removing the rod.

  Fichiers CAD 2D / 3D disponibles

  à partir de∗ ：	137.88 €
  Délai d'expédition minimum ：	5 jours

  *Prix unitaire/configuration de base

• 

  Adaptateurs pour prisme polariseur

  SURUGA SEIKI

  An adapter that can retain polarizing prisms and other similar items. Can be mounted to polarizer holders. Can be mounted to holders for F62, F63 and F64 elements which have a diameter of ø30.

  Fichiers CAD 2D / 3D disponibles

  à partir de∗ ：	90.31 €
  Délai d'expédition minimum ：	10 jours

  *Prix unitaire/configuration de base

• 

  Supports de polariseur

  SURUGA SEIKI

  [Features]
  · A holder used for retaining and rotating polarizing plates, polarizing filters, and wave plates, etc.
  · Can be manually rotated 360°.

  Fichiers CAD 2D / 3D disponibles

  à partir de∗ ：	171.58 €
  Délai d'expédition minimum ：	10 jours

  *Prix unitaire/configuration de base

• 

  Supports de polariseur (axe optique : 25 mm, réglage fin)

  SURUGA SEIKI

  [Features]
  · A holder used for retaining and rotating polarizing plates, polarizing filters, and wave plates, etc.
  · The optical axis height is standardized at 25 mm from the bottom.
  · Uses a threaded ring to fix devices.
  · An M4 male-threaded rod is attached.

  Fichiers CAD 2D / 3D disponibles

  à partir de∗ ：	252.03 €
  Délai d'expédition minimum ：	10 jours

  *Prix unitaire/configuration de base

• 

  Support à mouvement transversal (modèle □60)

  SURUGA SEIKI

  [Features]
  · A holder that can support and fix various types of adapter, and finely adjust them in the YZ axes and Yzθyθz axes.
  · 0.5 mm screws are used for the fine movement parts.
  · The F02-1E has a thickness of just 10 mm, and so is ideal for use in tight spaces or in close proximity to other types.
  · For the F02-1E type, fine movement of the YZ axes can be made using the operating screw. For the F02-4E type, fine movement of the Yzθyθz axes can be made

  Fichiers CAD 2D / 3D disponibles

  à partir de∗ ：	252.60 €
  Délai d'expédition minimum ：	5 jours

  *Prix unitaire/configuration de base

• 

  Supports à mouvement transversal, type plaque

  SURUGA SEIKI

  [Features]
  · A holder that can support and fix various types of adapter, and finely adjust them in the YZ axes and Yzθyθz axes.
  · A plate type cross motion holder with good stability and which can be used for experiments with low optical axes.
  · 0.5 mm screws are used for the fine movement parts.
  · For the F02-1E type, fine movement of the YZ axes can be made using the operating screw. For the F02-4E type, fine movement of the Yzθyθz axes can be made

  Fichiers CAD 2D / 3D disponibles

  à partir de∗ ：	261.59 €
  Délai d'expédition minimum ：	9 jours

  *Prix unitaire/configuration de base

• 

  Support de fixation, modèle sur semi-support

  SURUGA SEIKI

  [Features]
  · The mounting position of various types of adapter plate can by adjusted in the YZ axes.
  · Since the mounting position is fixed with screws, it will not move after being fixed.
  · Since the adapter plate is mounted using screws in two locations on the bottom side and there is no obstruction on the upper side, it is easy to handle from the top.
  · Use where no changes will be made once adjusted, such as adjusting the optical axis of lenses.

  Fichiers CAD 2D / 3D disponibles

  à partir de∗ ：	77.30 €
  Délai d'expédition minimum ：	10 jours

  *Prix unitaire/configuration de base

• 

  Fente variable

  SURUGA SEIKI

  [Features]
  · A double door type variable slit.
  · The slit width is adjusted using the micrometer head.
  · The slit width and the position of the center are constant.
  · V-groove rails and cross rollers are used for the double door slit section guide, decreasing the tilt of the slits during operation.
  · Use a Hartmann plate to adjust the slit height.

  Fichiers CAD 2D / 3D disponibles

  à partir de∗ ：	855.09 €
  Délai d'expédition minimum ：	10 jours

  *Prix unitaire/configuration de base

• 

  Supports de trous pour broche variables

  SURUGA SEIKI

  The rotating disc features eight small-diameter holes of different sizes every 45°. Positioning for each hole is done by a click-stop method. Note: The CAD data for this series is being modified. This data will be made available as soon as the modifications have been completed.

  Fichiers CAD 2D / 3D disponibles

  à partir de∗ ：	163.27 €
  Délai d'expédition minimum ：	5 jours

  *Prix unitaire/configuration de base

• 

  Porte-lentilles, modèle coaxial

  SURUGA SEIKI

  A holder that can fix lenses of any diameter and always keep the center of the held lens constant. Note: The CAD data for this series is being modified. This data will be made available as soon as the modifications have been completed.

  Fichiers CAD 2D / 3D disponibles

  à partir de∗ ：	162.29 €
  Délai d'expédition minimum ：	5 jours

  *Prix unitaire/configuration de base

• 

  Adaptateur à rotation

  SURUGA SEIKI

  [Features]
  · An adapter for attaching and rotating adapters for FC connectors and adapters for ferrules.
  · Used by attaching to various types of cross motion holder.
  · When using, fix the rotation adapter in the holder and then set the adapter and device.
  · The scale features degrees markings every 1°.
  

  Fichiers CAD 2D / 3D disponibles

  à partir de∗ ：	134.97 €
  Délai d'expédition minimum ：	10 jours

  *Prix unitaire/configuration de base

• 

  Support de fixation, modèle sur support

  SURUGA SEIKI

  Can retain and fix various types of adapter. The optical axis height is standardized at 25 mm from the bottom. Note: The CAD data for this series is being modified. This data will be made available as soon as the modifications have been completed.

  Fichiers CAD 2D / 3D disponibles

  à partir de∗ ：	38.20 €
  Délai d'expédition minimum ：	5 jours

  *Prix unitaire/configuration de base

• 

  Adaptateur pour lentille d'objectif

  SURUGA SEIKI

  Used by attaching to various types of cross motion holder.
  
  [Features]
  · An adapter for objective lenses.
  · Used by attaching to various types of cross motion holder.
  · The objective lens is fixed by screwing in.

  Fichiers CAD 2D / 3D disponibles

  à partir de∗ ：	38.20 €
  Délai d'expédition minimum ：	5 jours

  *Prix unitaire/configuration de base

Loading...