• 10 millions de produits
  • Livraison le jour même pour 30.000 articles en stock
  • Prix concurrentiels

Nos horaires d'ouverture: 08:00-17:00 (Lun au Jeu) et 08:00-16:00 (Ven)

Recherche par
catégorie ou fournisseur

Recherche par catégorie
Composants mécaniques
Vis, boulons, rondelles, écrous
Semi-finis
Câbles et Connecteurs
Automatisme et Contrôles
Outils coupants
Fournitures industrielles
Manutention et Stockage
Protection individuelle – Hygiène & Sécurité
Laboratoires et Salles blanches
Composants pour la fabrication d'outils d'estampage
Composants pour la fabrication de moules d'injection

Recherche par marque
Marques représentées

Supports laser

  • Données à afficher
    30
    45
    60
  • Trier
Nombre de jours d'expédition
  • Tous les articles
  • 8 jours ou moins
  • 9 jours ou moins
  • Supports de capteur/laser

    Supports de capteur/laser

    SURUGA SEIKI

    [Features] - Tilt adjustments for the small sensor and laser point. - Please feel free to use for the mounting of various adapter plates as P.C.D.32 tapping holes are drilled onto the holder surface.

    CAD
    2D3D
    à partir de
    114.75€
    Délai de livraison minimum
    8 jours

    *Prix unitaire/configuration de base

  • Adaptateur refroidi par eau

    Adaptateur refroidi par eau

    SURUGA SEIKI

    [Features] - A water cooling adapter for use with LD holders F125/F126/F127. - Better temperature stability and lower temperature control are possible by connecting to the low-temperature circulating water bed. - Please connect by using a 1/4 inch hose (the hose is not included)

    CAD
    2D3D
    à partir de
    92.15€
    Délai de livraison minimum
    8 jours

    *Prix unitaire/configuration de base

  • Support à laser rond

    Support à laser rond

    SURUGA SEIKI

    [Features] - F20 holds the laser between three screws and the light axis is adjusted by turning the screws in and out. - For F21, in addition to the F20 functions, it is possible to adjust the θγ direction by operating the screws on the lower portion of the holder. - For both the F20 and F21, there are the two types of L = 150 and 250 according to the laser length. - The standard rod that is included is ø 20 and L = 60 but it is possible to change both the rod diameter and length as desired. - The laser holder section can be fixed to a position 50mm shifted from the gap by removing the fixation screw from the under side (F20-150 and 250 only). - For F20, the rod can be removed and mounted directly on the breadboard (A65).

    CAD
    2D3D
    à partir de
    116.79€
    Délai de livraison minimum
    8 jours

    *Prix unitaire/configuration de base

  • Support LD

    Support LD

    SURUGA SEIKI

    F511L: Stationary type. F512L and F513L: The LD holder has an adjustable YZ axis. Please make a selection in accordance with the LD number of pins and pin pitch (pin P.C.D).

    CAD
    2D3D
    à partir de
    97.98€
    Délai de livraison minimum
    8 jours

    *Prix unitaire/configuration de base

  • Support LD (Modèle pour paquet)

    Support LD (Modèle pour paquet)

    SURUGA SEIKI

    [Features] - To-Package type LD holder with Peltier element. - Uses embedded Peltier element to equip the calibrated 10 kΩ thermistor sensor - LD sizes ø 5.6 (pin PCD, 2.0) and ø 9.0 (pin PCD, 2.54) respectively support 3-pin and 4-pin. - The anode common and cathode common are set by switching the jumper pins. - For the connector, D-sub9 pin female is used for LD drive and D-sub9 pin male is used for the temperature controller. - Water cooling adapter F129-1 is also available. - Stability and low-temperatures are possible by using the low-temperature circulating water tank.

    CAD
    2D3D
    à partir de
    531.80€
    Délai de livraison minimum
    Devis

    *Prix unitaire/configuration de base

  • Supports LD (modèle de porte-puce)

    Supports LD (modèle de porte-puce)

    SURUGA SEIKI

    [Features] - LD holder for the Chip Carrier type with Peltier element embedded. - Uses embedded Peltier element to equip the calibrated 10 kΩ thermistor sensor. - The LD anode and cathode switch can be set by switching the jumper pins. - There are two types of Chip Carrier type LD holders. These are set by mounting the LD (radiation direction). - For the connector, D-sub9 pin female is used for LD drive and D-sub9 pin male is used for the temperature controller. - Water cooling adapter F129-1 is also available. - Stability and low-temperatures are possible by using the low-temperature circulating water tank.

    CAD
    2D3D
    à partir de
    531.80€
    Délai de livraison minimum
    9 jours

    *Prix unitaire/configuration de base

Configurer

Réinitialiser

Affiner la recherche en spécifiant le fabricant

Marque

Activité produits circulation publique MISUMI

Affiner la recherche en précisant le type de données CAO

Sélectionner l'image

Fermer