Size		10	15	20	30	40
Rotating angle		90°, 180°, 270 °
Fluid		Air (non-lube)
Proof pressure (MPa)		1.05			1.5
Ambient and fluid temperature		5 to 60°C
Max. operating pressure (MPa)		0.7			1.0
Min. operating pressure (MPa)		0.2	0.15
Rotation time adjustment range (s/90)°^*1		0.03 to 0.3			0.04 to 0.3	0.07 to 0.5
Allowable kinetic energy (J)^*2		0.00015	0.001	0.003	0.02	0.04
Allowable kinetic energy (J)^*2		0.00015	0.00025	0.0004	0.015	0.03
Shaft load (N)	Allowable radial load	15	15	25	30	60
Shaft load (N)	Allowable thrust load	10	10	20	25	40
Port location		Side ported or Axial ported
Port size (side ported, axial ported)		M3 × 0.5		M5 × 0.8
Angle adjustable range^*3		0 to 230 °	0 to 240 °			0 to 230 °

*1Make sure to operate within the speed regulation range. Exceeding the maximum speed (0.3 s/90°) can cause the unit to stick or not operate.
For size 10, when operation at the maximum speed (0.03 s/90°) is required, the operating pressure should be set to 0.35 MPa or higher.
*2The upper numbers in this section in the table indicate the energy factor when the rubber bumper is used (at the end of the rotation), and the lower numbers indicate the energy factor when the rubber bumper is not used.
*3Adjustment range in the table is for 270°. For 90° and 180°, refer to the manufacturer's catalog.

Size		10	15	20	30	40
Rotating angle		90°, 100 °
Fluid		Air (non-lube)
Proof pressure (MPa)		1.05			1.5
Ambient and fluid temperature		5 to 0°C
Max. operating pressure (MPa)		0.7			1.0
Min. operating pressure (MPa)		0.2	0.15
Rotation time adjustment range (s/90)°^*1		0.03 to 0.3			0.04 to 0.3	0.07 to 0.5
Allowable kinetic energy J		0.0003	0.0012	0.0033	0.02	0.04
Shaft load (N)	Allowable radial load	15	15	25	30	60
Shaft load (N)	Allowable thrust load	10	10	20	25	40
Port location		Side ported or Axial ported
Port size (side ported, axial ported)		M3 × 0.5		M5 × 0.8
Angle adjustable range^*2		0 to 90 °

*1Make sure to operate within the speed regulation range. Exceeding the maximum speed (0.3 s/90°) can cause the unit to stick or not operate.
For size 10, when operation at the maximum speed (0.03 s/90°) is required, the operating pressure should be set to 0.35 MPa or higher.
*2Adjustment range in the table is for 100°. For 90°, see the manufacturer's catalog.

*For single vane type, the following figures show actuators for 90° and 180° when B port is pressurized.
*For double vane type, the following figures show the intermediate rotation position when A or B port is pressurized.

(Unit: mm)

Single shaft / Port location: side ported

(Unit: mm)

Double shaft / Port location: side ported

(Unit: mm)

Shaft-end shape of size 40

(Unit: mm)

Single shaft / Port location: side ported

(Unit: mm)

Size 10 (port location: side ported)

(Unit: mm)

Size 10, 15, 20, 30, 40 (port location: axial ported)

(Unit: mm)

Size	A	B	C	D	E (g7)	F (h9)	G1	G2	J	K	L	M	N	P
Size	A	B	C	D	E (g7)	F (h9)	G1	G2	J	K	L	M	N	P
10	29	15	8	14	4 (-0.016 to -0.004)	9 (-0.036 to 0)	3	1	5	9	0.5	9.5	9.5	24
15	34	20	9	18	5 (-0.016 to -0.004)	12 (-0.043 to 0)	4	1.5	6	10	0.5	14	10	29
20	42	29	10	20	6 (-0.016 to -0.004)	14 (-0.043 to 0)	4.5	1.5	7	10	0.5	20	13	36
30	50	40	13	22	8 (-0.020 to -0.005)	16 (-0.043 to 0)	5	2	8	12	1.0	26	14	43
40	63	45	15	30	10 (-0.020 to -0.005)	25 (-0.052 to 0)	6.5	4.5	9	20	1.0	31	20	56

The following figures show the intermediate rotation position when A or B port is pressurized.

(Unit: mm)

Single shaft / Port location: side ported

(Unit: mm)

Double shaft / Port location: side ported

(Unit: mm)

(Port location: axial ported)

*Refer to the manufacturer's catalog for other models' dimensions, specifications, etc.