Freely Specifiable Straight Blade End Mills Recommended Cutting Conditions

Side-cutting with End Mills for Carbide Straight Blade T-Slot Machining

Title image sample
● This table was made based on an Rd (cut-in width) of 0.1 to 0.2 D and an Ad (flute width) of 2 mm.
● Use a machine and chuck that have rigidity and high accuracy.
● Select cutting oil suitable for the work material.
● Cutting conditions also change when the blade portion is shaped. So adjust the optimum cutting conditions by referring to the table below.
● For fraction sizes of flute diameter D, refer to the larger of the number values.
● Use Slim Shanks (SS-) at both feed speeds and rotational speeds 70% of the following conditions.

(T-slot 2 Flutes) Model Number Example
STSEM / STSBEM / STSREM, etc.

Title image sample

(T-slot 4 Flutes) Model Number Example
STSEMW / STSBEMW / STSREMW, etc.

Title image sample

Groove Cutting with End Mills for Carbide Straight Blade T-Slot Machining

Title image sample
● Use a machine and chuck that have rigidity and high accuracy.
● Select cutting oil suitable for the work material.
● Use Slim Shanks (SS-) at both feed speeds and rotational speeds 70% of the following conditions.
● Cutting conditions also change when the blade portion is shaped. So adjust the optimum cutting conditions by referring to the table below.
● For fraction sizes of flute diameter D, refer to the larger of the number values.

(T-slot 2 Flutes) Model Number Example
STSEM / STSBEM / STSREM, etc.

Title image sample

(T-slot 4 Flutes) Model Number Example
STSEMW / STSBEMW / STSREMW, etc.

Title image sample

Cutting with End Mills for Carbide Straight Blade Boss Machining

Title image sample
● This table was made based on the machining conditions on the left.
● Use a machine and chuck that have rigidity and high accuracy.
● Select cutting oil suitable for the work material.
● If the rotational speed does not increase with your machine, lower the feed rate and rotational speed at the same ratio.
● Use Long Shanks (LS-) at both amounts of feed and rotational speeds 70% of the following conditions.

Model Number
BSC / BSRC / BSCC / BSCAC / BSCACR / BSCADC / BSTC / BSTRC / BSTCC / BSTCAC / BSTCADC

Title image sample

Rounded Corner Machining with a Carbide Inner Curve Cutter

Title image sample
● Cutting should be conducted in multiple separate bursts.
● Use a machine and chuck that have rigidity and high accuracy.
● Select cutting oil suitable for the work material.
● If the rotational speed does not increase with your machine, lower the table feed rate and rotational speed at the same ratio.

Model Number
SCREM/SCRDEM

Title image sample

Groove Cutting with Freely Specifiable Straight Blade End Mills

Title image sample
● This table was made based on an Ad (cut depth) of 0.5 to 1.0 D.
● Use a machine and chuck that have rigidity and high accuracy.
● Select cutting oil suitable for the work material.
● Cutting conditions also change when the blade portion is shaped. So adjust the optimum cutting conditions by referring to the table below.
● For fraction sizes of flute diameter D, refer to the larger of the number values.
● Use Long Shanks (LS-) at both feed speeds and rotational speeds 70% of the following conditions.

Model Number
SEM / SBEM / SHBEM / SQBEM / SFBEM / SHBTEM / SBTEM / NR-SBTEM / NR-SHBTEM / SLBEM / SREM /
SCEM / STEM / STBEM / STREM / STCEM / SCAEM / STCAEM / SCADEM / STCADEM / SCAREM / SSBTEM

Title image sample

Side-cutting with Freely Specifiable Straight Blade End Mills

Title image sample
● This table was made based on an Rd (cut width) of 0.1 to 0.2 D and an Ad (cut depth) of 1.0 to 1.5 D.
● Use a machine and chuck that have rigidity and high accuracy.
● Select cutting oil suitable for the work material.
● Cutting conditions also change when the blade portion is shaped. So adjust the optimum cutting conditions by referring to the table below.

● For fraction sizes of flute diameter D, refer to the larger of the number values.
● Use Long Shanks (LS-) at both feed speeds and rotational speeds 70% of the following conditions.

Model Number
SEM / SBEM / SHBEM / SQBEM / SFBEM / SHBTEM / SBTEM / SLBEM / SREM / SCEM / STEM /
STBEM / STREM / STCEM / SCAEM / STCAEM / SCADEM / STCADEM / SCAREM / SCAEMR

Title image sample

Cutting with End Mills for Freely Specifiable Straight Blade Stepped Boss Hole Drilling

Title image sample
● This table was made based on the machining conditions on the left.
● Use a machine and chuck that have rigidity and high accuracy.
● Select cutting oil suitable for the work material.

● If the rotational speed does not increase with your machine, lower the feed rate and rotational speed at the same ratio.


Model Number
BSCS

Title image sample

Groove Cutting with End Mills for Freely Specifiable Straight Blade Stepped Machining

Title image sample
●This table was made based on an Ad (blade cut depth) of 0.5 to 1.0 D.
● Use a machine and chuck that have rigidity and high accuracy.
● Select cutting oil suitable for the work material.
● If the rotational speed does not increase with your machine, lower the feed rate and rotational speed at the same ratio.
● For fraction sizes of flute diameter D, refer to the larger of the number values.

Model Number
SEMS

Title image sample

Cutting with Freely Specifiable Straight Blade End Mills

Title image sample
● Use a machine and chuck that have rigidity and high accuracy.
● Select cutting oil suitable for the work material.
● If the rotational speed does not increase with your machine, lower the feed rate and rotational speed at the same ratio.
● Use Long Shanks (LS-) at both amounts of feed and rotational speeds 70% of the following conditions.

Model Number
SRM / BSRM / SSCMEM / BSZEM / SBRM / SRRM / SRCMEM / SCRM / BSCRM / SCCMEM /
BSZCEM / SCARM / BSCARM / SCACMEM / BSZCAEM / STCMEM / STBCMEM / STRCMEM /
STCCMEM / STCACMEM / SBCREM / SRCREM / SCCREM / SCACREM / SZEM / SZBEM / SZREM /
SZCEM / STCREM / STBCREM / STRCREM / STCCREM / STCACREM / SZREM / BSZREM

Title image sample

Side-cutting with Freely Specifiable Straight Blade End Mills

Title image sample
● This table was made based on an Ad (cut depth) of 0.5 to 1.0 D.
● Use a machine and chuck that have rigidity and high accuracy.
● Select cutting oil suitable for the work material.
● Cutting conditions also change when the blade portion is shaped. So adjust the optimum cutting conditions by referring to the table below.
● For fraction sizes of flute diameter D, refer to the larger of the number values.
● Use Long Shanks (LS-) at both feed speeds and rotational speeds 70% of the following conditions.

Model Number
SSCREM / SBCREM / SRCREM / SCACREM / SZEM / SZBEM / SZREM / SZCEM /
SZCAEM / STCREM / STBCREM / STRCREM / STCCREM / STCACREM / SCRTEM

Title image sample

V Groove, Positioning and Chamfering by Freely Specifiable Straight Blade End Mills

Title image sample
● Chamfer machining conditions where Ad (cutting depth) is 0.3 D or less.
● When V groove machining, use at 50% or less of the criteria listed below.
● Use a machine and chuck that have rigidity and high accuracy.
● Select cutting oil suitable for the work material.
● If the rotational speed does not increase with your machine, lower the feed rate and rotational speed at the same ratio.
● For fraction sizes of flute diameter D, refer to the larger of the number values.
● Use Long Shanks (LS-) at both feed speeds and rotational speeds 70% of the following conditions.

Model Number
SVEM / SVZEM / SMBEM / SMEM / SVDEM

Title image sample

Groove Cutting with Carbide Ring Groove Cutters

Title image sample

Model Number
C-RGC

Title image sample

Back to Top