MY1H-Z, Vérin sans tige à entraînement direct, Type de guide linéaire sans bloc butée
[Features]
· Piping on site is adjustable depending on the state of the installation.
· Adjusting the cushion needle is easy.
(i)Remarque
- Les photos des produits sont des représentations. Les données CAO ne sont pas prises en charge par certains numéros de modèle.
Référence pièce
Vous pouvez trouver ici le numéro
de référence lié au produit recherché.
Mechanically Jointed Rodless Cylinder, Linear Guide Type, MY1H-Z Series Specifications
Model Indication Method
Model indication method, image
Compatible auto switches
| Type | Special function | Lead wire outlet | Indicator light | Wiring (output) | Load voltage | Auto switch part number | Lead wire length (m) | Pre-wired connector | Compatible load | ||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| DC | AC | Vertical outlet | Lateral outlet | 0.5 (no mark) | 1 (M) | 3 (L) | 5 (Z) | None (N) | |||||||||
| Non-contact auto switch | - | Grommet | Available | 3-wire (NPN) | 24 V | 5 V, 12 V | - | M9NV | M9N | ● | ● | ● | ○ | ○ | ○ | IC circuit | Relay, PLC |
| 3-wire (PNP) | M9PV | M9P | ● | ● | ● | ○ | ○ | ○ | |||||||||
| 2-wire | 12 V | M9BV | M9B | ● | ● | ● | ○ | ○ | ○ | - | |||||||
| Diagnostic display (2-color display) | 3-wire (NPN) | 5 V, 12 V | M9NWV | M9NW | ● | ● | ● | ○ | ○ | ○ | IC circuit | ||||||
| 3-wire (PNP) | M9PWV | M9PW | ● | ● | ● | ○ | ○ | ○ | |||||||||
| 2-wire | 12 V | M9BWV | M9BW | ● | ● | ● | ○ | ○ | ○ | - | |||||||
| Part with enhanced water resistance (2-color display) | 3-wire (NPN) | 5 V, 12 V | Note 1M9NAV | Note 1M9NA | ○ | ○ | ● | ○ | - | ○ | IC circuit | ||||||
| 3-wire (PNP) | Note 1M9PAV | Note 1M9PA | ○ | ○ | ● | ○ | - | ○ | |||||||||
| 2-wire | 12 V | Note 1M9BAV | Note 1M9BA | ○ | ○ | ● | ○ | - | ○ | - | |||||||
| Contact auto switch | - | Grommet | Available | 3-wire (NPN equivalent) | - | 5 V | - | A96V | A96 | ● | - | ● | - | - | - | IC circuit | - |
| 2-wire | 24 V | 12 V | 100 V | Note 2A93V | A93 | ● | ● | ● | ● | - | - | - | Relay, PLC | ||||
| NA | 100 V or less | A90V | A90 | ● | - | ● | - | - | - | IC circuit | |||||||
- Note 1 Auto switches with enhanced water resistance can be mounted on the above model products, but that does not guarantee the water-resistant performance of the product.
Confirm with the manufacturer for regarding the above models with enhanced water resistance. - Note 2 The type with a 1 m lead wire only supports D-A93.
Specifications chart
| Tube inner diameter (mm) | 25 | 32 | 40 | |
|---|---|---|---|---|
| Usable fluids | Air | |||
| Operating type | Double-acting type | |||
| Operating pressure range | 0.1 to 0.8 MPa | |||
| Guaranteed pressure resistance | 1.2 MPa | |||
| Ambient temperature and working fluid temperature | 5 to 60°C | |||
| Cushion | Air cushion | |||
| Lubrication | Lubrication-free | |||
| Allowable difference of stroke length | 0 to +1.8 | |||
| Piping connection port diameter | Front/side port | Rc 1/8 | Rc 1/4 | |
| Bottom port | ø6 (diameter 6 mm) | ø8 (diameter 8 mm) | ||
Made-to-order specifications
| Display symbol | Specifications/details |
|---|---|
| -X168 | Helical coil insert screw specifications |
Made-to-order specifications
| Display symbol | Specifications/details |
|---|---|
| -XB10 | Intermediate stroke (dedicated body used) |
| -XB11 | Long stroke type |
| -XB22 | Shock absorber / soft type RJ series-equipped |
| -XC56 | Includes dowel pins |
Lock specifications
| Tube inner diameter (mm) | 25 | 32 | 40 |
|---|---|---|---|
| Lock position | One side (selectable), both sides | ||
| Retention (MAX.) N | 270 | 450 | 700 |
| Stroke adjustable range (mm) | 0 to -11.5 | 0 to -12 | 0 to -16 |
| Backlash | 1 mm or less | ||
| Manual unlock | Allowable (non-locking type) | ||
Operating piston speed
| Tube inner diameter (mm) | 25 to 40 | |
|---|---|---|
| No stroke adjustment unit | 100 to 1,000 mm/s | |
| Stroke adjustment unit | A unit | 100 to 1,000 mm/sNote 1) |
| L unit, H unit | 100 to 1,500 mm/sNote 2) | |
Note 1: Air cushioning performance is reduced when the adjusting bolt is used to increase the stroke adjustment. Meanwhile, in ranges exceeding the air cushion stroke, the working piston speed will become 100 to 200 mm/s.
Note 2: The working piston speed will become 100 to 1,000 mm/s when using centralized piping.
Note 3: Use at a speed within the range of the absorption capacity.
Stroke adjustment unit specifications
| Tube inner diameter (mm) | 25 | 32 | 40 | |||||||
|---|---|---|---|---|---|---|---|---|---|---|
| Unit symbol | A | L | H | A | L | H | A | L | H | |
| Configuration details Shock absorber model | Adjusting bolt included | RB 1007 + Adjusting bolt included | RB 1412 + Adjusting bolt included | Adjusting bolt included | RB 1412 + Adjusting bolt included | RB 2015 + Adjusting bolt included | Adjusting bolt included | RB 1412 + Adjusting bolt included | RB 2015 + Adjusting bolt included | |
| Stroke adjustment range of each spacer for intermediate fixing (mm) | No spacer | 0 to -11.5 | 0 to -12 | 0 to -16 | ||||||
| With short spacer | -11.5 to -23 | -12 to -24 | -16 to -32 | |||||||
| With long spacer | -23 to -34.5 | -24 to -36 | -32 to -48 | |||||||
- *The stroke adjustment range is the adjustment range of one side when attached to a cylinder.
Stroke adjustment unit symbol
| - | Right stroke adjustment unit | |||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|
| No unit | A: Adjusting bolt included | L: Shock absorber for low loads and adjusting bolt included | H: Shock absorber for high loads and adjusting bolt included | |||||||||
| - | With short spacer | With long spacer | - | With short spacer | With long spacer | - | With short spacer | With long spacer | ||||
| Left side stroke adjustment unit | No unit | No mark | SA | SA6 | SA7 | SL | SL6 | SL7 | SH | SH6 | SH7 | |
| A: Adjusting bolt included | - | AS | A | AA6 | AA7 | AL | AL6 | AL7 | AH | AH6 | AH7 | |
| With short spacer | A6S | A6A | A6 | A6A7 | A6L | A6L6 | A6L7 | A6H | A6H6 | A6H7 | ||
| With long spacer | A7S | A7A | A7A6 | A7 | A7L | A7L6 | A7L7 | A7H | A7H6 | A7H7 | ||
| L: Shock absorber for low loads and adjusting bolt included | - | LS | LA | LA6 | LA7 | L | LL6 | LL7 | LH | LH6 | LH7 | |
| With short spacer | L6S | L6A | L6A6 | L6A7 | L6L | L6 | L6L7 | L6H | L6H6 | L6H7 | ||
| With long spacer | L7S | L7A | L7A6 | L7A7 | L7L | L7L6 | L7 | L7H | L7H6 | L7H7 | ||
| H: Shock absorber for high loads and adjusting bolt included | - | HS | HA | HA6 | HA7 | HL | HL6 | HL7 | H | HH6 | HH7 | |
| With short spacer | H6S | H6A | H6A6 | H6A7 | H6L | H6L6 | H6L7 | H6H | H6 | H6H7 | ||
| With long spacer | H7S | H7A | H7A6 | H7A7 | H7L | H7L6 | H7L7 | H7H | H7H6 | H7 | ||
- *The spacer for intermediate fixing of the stroke adjustment unit cannot be used on the side to when the end lock is attached.
- *The spacer is a mounting bracket for fixing the stroke adjustment unit in an intermediate position of the stroke.
The model number of the shock absorber for the L and H units
| Type | Stroke adjustment unit | Tube inner diameter (mm) | ||
|---|---|---|---|---|
| 25 | 32 | 40 | ||
| Standard (shock absorber RB series) | L | RB1007 | RB1412 | |
| H | RB1412 | RB2015 | ||
| Shock absorber / soft type RJ series-equipped (-XB22) | L | RJ1007H | RJ1412H | |
| H | RJ1412H | - | - | |
- *The lifespan of the shock absorber is different from that of the MY1H cylinder main body.
- *The shock absorber / soft type RJ series-equipped (-XB22) has made-to-order specifications.
Shock absorber specifications
| Model | RB 1007 | RB 1412 | RB 2015 | |
|---|---|---|---|---|
| Maximum energy absorption (J) | 5.9 | 19.6 | 58.8 | |
| Stroke absorption (mm) | 7 | 12 | 15 | |
| Maximum collision velocity (mm/s) | 1,500 | 1,500 | 1,500 | |
| Maximum operating frequency (cycle/min) | 70 | 45 | 25 | |
| Spring force (N) | When expanded | 4.22 | 6.86 | 8.34 |
| When compressed | 6.86 | 15.98 | 20.50 | |
| Operating temperature range (°C) | 5 to 60 | |||
- *The lifespan of the shock absorber will differ from that of the MY1H cylinder main body depending on the use conditions.
Standard type, structural drawing
Standard type, structural drawing
Components
| Number | Description | Materials | Additional notes |
|---|---|---|---|
| 1 | Cylinder tube | Aluminum alloy | Hard anodized aluminum |
| 2 | Head cover | Aluminum alloy | Painted |
| 3 | Cushion boss | Special resin | - |
| 4 | Slide table | Aluminum alloy | Hard anodized aluminum |
| 5 | Piston yoke | Aluminum alloy | Chromate |
| 6 | Piston | Aluminum alloy | Chromate |
| 7 | Wear ring | Special resin | - |
| 8 | Belt separator | Special resin | - |
| 9 | Guide roller | Special resin | - |
| 10 | Parallel pin | Stainless steel | - |
| 11 | Coupler | Ferrous sintered material | - |
| 12 | Head plate | Stainless steel | - |
| 13 | Cushion needle | Rolled steel | Nickel plating |
| 14 | Belt clamp | Special resin | - |
| 17 | Guide | - | - |
| 18 | End cover | Special resin | - |
| 20 | Steel ball | Carbon tool steel | - |
| 21 | Bearing | Special resin | - |
| 22 | Magnet | Rare earth magnet | - |
| 23 | Square nut | Carbon steel | Chromate |
| 24 | Spring pin | Bearing steel | - |
| 26 | Thin-head screw | Chrome molybdenum steel | Chromate |
| 27 | Hex socket head bolt | Chrome molybdenum steel | Chromate |
| 28 | Hex socket head bolt | Chrome molybdenum steel | Chromate |
| 29 | Hex socket head bolt | Chrome molybdenum steel | Chromate |
| 33 | Hex socket head taper plug (tapered) | Carbon steel | Chromate (in the case of centralized piping: 10 pcs.) |
| 34 | Hex socket head taper plug (tapered) | Carbon steel | Chromate (in the case of centralized piping: 4 pcs.) |
| 38 | Stopper | Carbon steel | - |
| 39 | Spacer | Stainless steel | - |
| 40 | Hex socket head cap button screw | Chrome molybdenum steel | Chromate |
| 41 | CR-type retaining ring | Steel for springs | - |
| 42 | Seal magnet | Rubber magnet | - |
| 43 | Lub-retainer | Special resin | - |
Replacement parts / seal kit
| Number | Description | Materials | Quantity | MY1H25 | MY1H32 | MY1H40 |
|---|---|---|---|---|---|---|
| 15 | Seal belt | Urethane | 1 | MY25-16C-[stroke] | MY32-16C-[stroke] | MY40-16C-[stroke] |
| 16 | Dust seal band | Stainless steel | 1 | MY1B25-16B-[stroke] | MY1B32-16B-[stroke] | MY1B40-16B-[stroke] |
| 25 | Cushion boss gasket | NBR | 2 | MYB25-16GA5900 | MYB32-16GA5901 | MYB40-16GA5902 |
| 36 | O-ring | NBR | 2 | KA00311 | KA00320 | KA00320 |
| (ø5.1 (diameter 5.1 mm) ×; ø3 (diameter 3 mm ×; ø1.05 (diameter 1.05 mm)) | (ø7.15 (diameter 7.15 mm) ×; ø3.75 (diameter 3.75 mm) ×; ø1.7 (diameter 1.7 mm)) | (ø7.15 (diameter 7.15 mm) ×; ø3.75 (diameter 3.75 mm) ×; ø1.7 (diameter 1.7 mm)) | ||||
| 37 | Side scraper | Special resin | 2 | MYH25-15BK2902B | MYH32-15BK2903B | MYH40-15BK2904B |
| 19 | Scraper | NBR | 2 | MY1H25-PS | MY1H32-PS | MY1H40-PS |
| 30 | Piston packing | NBR | 2 | |||
| 31 | Cushion seal | NBR | 2 | |||
| 32 | Tube gasket | NBR | 2 | |||
| 35 | O-ring | NBR | 2 |
- *Because the seal kit includes 19, 30, 31, 32, and 35, order using the order number of each tube inner diameter.
- *The seal kit includes a grease pack (10 g).
A grease pack (20 g) is included when 15 or 16 are shipped as single items.
End lock structural drawing
End lock structural drawing
Components
| Number | Description | Materials | Additional notes |
|---|---|---|---|
| 1 | Body for locking | Aluminum alloy | Painted |
| 2 | Lock finger | Carbon steel | Nickel plating after quenching |
| 3 | Lock finger fixture | Rolled steel | Nickel plating |
| 4 | Lock piston | Carbon tool steel material | Kanizen plating after quenching |
| 5 | Rod cover | Aluminum alloy | Hard anodized aluminum |
| 6 | Return spring | Spring steel | Zinc chromate |
| 7 | Bypass pipe | Aluminum alloy | Hard anodized aluminum |
| 10 | Steel ball | High-carbon chromium bearing steel | - |
| 11 | Steel ball | High-carbon chromium bearing steel | - |
| 13 | Round R-shaped retaining ring | Carbon tool steel | Nickel plating |
| 15 | Hex socket head bolt | Chrome molybdenum steel | Chromate |
| 16 | Hex socket head bolt | Chrome molybdenum steel | Chromate |
| 17 | Steel ball | High-carbon chromium bearing steel | - |
| 18 | Steel ball | High-carbon chromium bearing steel | - |
| 19 | Head cover WR | Aluminum alloy | Painted |
| 20 | Head cover WL | Aluminum alloy | Painted |
| 21 | Cushion ring | Aluminum alloy | - |
| 22 | Hex socket set screw | Chrome molybdenum steel | Chromate |
Replacement parts / seal kit
| Number | Part name | Materials | Quantity | MY1H25 | MY1H32 | MY1H40 |
|---|---|---|---|---|---|---|
| 8 | Rod packing | NBR | 1 | KB00267 | KB00267 | KB00267 |
| 9 | Piston packing | NBR | 1 | KB00217 | KB00217 | KB00217 |
| 12 | O-ring | NBR | 1 | KB00037 | KB00037 | KB00037 |
| 14 | O-ring | NBR | 2 | KA00048 | KA00048 | KA00048 |
- *The packing does not include a grease pack; please make arrangements separately.
Référence pièce
|
|---|
| MY1H25-1500HZ |
| MY1H40-1500Z |
| Référence pièce | Relatif à |
Prix unitaire standard
| Quantité minimale de commande | Remise sur volume | Type | Course (mm) | Matériau de la table | Poids de charge maximum (montage à l'horizontale) (kg) | Max. Masse de la charge (kg) | Longueur de la table L (mm) | D.I. du cylindre (Ø) | Type à joint de cylindre sans tige | Environnement de fonctionnement | Traitement de surface de la table | Guide | Largeur de la table W (mm) | Hauteur de la table H (mm) | Pression de fonctionnement (MPa) | Piping Format | Port Screw Type | Cushion | Auto Switch | Lead Wire Length (m) | Number of Switches | Custom-made Specifications | End Block | Model | Stroke Adjustment Unit Symbol | Custom-made | Spacer for intermediate fixing | Spacer shipping form | Type | Applicable inner diameter of cylinder (ø) | |
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| - | 2,465.37 € | 1 | 9 jours | Vérin sans tige | 1,500 | [Aluminium] Alliage d'aluminium | 20 to 39.9 | 27.5 | 114 | 25 | Assemblage mécanique | Usage général | [Anodisé clair] Aluminium anodisé dur | [Guide roulant] Type à guide linéaire | 90 | 54 | 0,1 à 0,8 | Type standard | Rc | Coussin d'air | - | Aimant intégré | Aucun | - | Aucun | - | - | Aucun | - | - | Vérin | - | ||
3,144.89 € | 1 | 9 jours | Vérin sans tige | 1,500 | [Aluminium] Alliage d'aluminium | 40 to 57 | 50 | 170 | 40 | Assemblage mécanique | Usage général | [Anodisé clair] Aluminium anodisé dur | [Guide roulant] Type à guide linéaire | 121 | 84 | 0,1 à 0,8 | Type standard | Rc | Coussin d'air | - | Aimant intégré | Aucun | - | Aucun | - | - | Aucun | - | - | Vérin | - |
Loading...
Configurer
Propriétés de base
-
Type
- Vérin sans tige
- Autre
-
Matériau de la table
- Aluminium
- Aluminium
-
Poids de charge maximum (montage à l'horizontale)(kg)
-
Max. Masse de la charge(kg)
-
Longueur de la table L(mm)
-
D.I. du cylindre(Ø)
-
Type à joint de cylindre sans tige
- Assemblage mécanique
-
Environnement de fonctionnement
- Usage général
-
Traitement de surface de la table
- Anodisé clair
- Anodisé clair
-
Guide
- Guide roulant
- Guide roulant
-
Largeur de la table W(mm)
-
Hauteur de la table H(mm)
-
Pression de fonctionnement(MPa)
-
Piping Format
- Type standard
- Type à tuyauterie centralisée
-
Port Screw Type
- G
- NPT
- Rc
-
Cushion
- Coussin d'air
-
Auto Switch
- M9B
- M9BW
- M9BWV
- M9P
- M9PW
- A93
- Aucun
- Sans
-
Lead Wire Length(m)
- 0.5
- 3
- Aimant intégré
-
Number of Switches
- 2
- M9B
- M9BA
- M9BV
- M9BW
- M9P
- M9PW
- A93
- Aucun
-
Custom-made Specifications
- 0.5
- 3
-
End Block
- Aucun
-
Model
-
Stroke Adjustment Unit Symbol
- 0.1 à 0.8
- H6
- H6H
- HH6
- L6
- L6L
- SL6
- A6L6
- L6A6
- A6H7
- H6H7
- H7
- HH7
- HL7
- L7
- LL7
- SL7
- L7L6
- A
- AH
- AL
- H
- HS
- L
- LH
- LS
- No unit
- SL
- Sans bloc
-
Custom-made
- Aucun
- Avec trous de tenon
- Spécifications de l’insert hélicoïdal de filetage
-
Spacer for intermediate fixing
- Entretoise courte
- Entretoise longue
- Sans entretoise
-
Spacer shipping form
- Entretoise uniquement
- Unité intégrée
-
Type
- Unité de réglage de course
- Vérin
-
Applicable inner diameter of cylinder(ø)
-
Type
- MY1H-Z
- MYH-A
-
Course(mm)
-
Filtrer par type de données CAO
- 2D
- 3D
Filtrer par jours d'expédition standard
-
- Tous les articles
- 4 jours ou moins
- 7 jours ou moins
- 8 jours ou moins
- 9 jours ou moins
- 14 jours ou moins
- 16 jours ou moins
- 17 jours ou moins
- 22 jours ou moins
- 26 jours ou moins
- 98 jours ou moins
Propriétés optionnelles
- Les spécifications et les dimensions de certaines pièces peuvent ne pas être intégralement indiquées. Pour plus de détails, reportez-vous aux catalogues des fabricants .
Assistance technique
Mode de paiement
Fabrication à la demande
Certificats
Copyright © MISUMI Corporation All Rights Reserved.