GANTER Autres charnières et accessoires pour charnières

?* À propos du délai d'expédition et des prix

• 

  Charnières d'angle / bonlon / acier / GN 129 / GANTER

  GANTER

  Hinges GN 129 are used for doors which are flush with the frame on the outside. The hinges are normally arranged to the side of the door.
  In the two-part design, the door can be unhinged with two identically arranged hinges.
  The three-part hinges, which generally cannot be unhinged and are mounted inside, are suitable for doors and flaps which, as anti-tamper precaution, must not be dismountable from the outside.

  • Remise sur volume

  Fichiers CAD 2D / 3D disponibles

  à partir de∗ ：	8.90 €
  Délai d'expédition minimum ：	Jour même

  *Prix unitaire/configuration de base

• 

  Charnières d'angle amovible / filetage intérieur / zinc / GN 161.1 / GANTER

  GANTER

  Hinges GN 161.1 are a variant with highly attractive design. The fixing screws are invisible.
  During the load tests, the hinges were gradually loaded and relieved at room temperature with incrementally increasing force.
  For the specified values, an insignificant permanent deformation remained after relieving the load which had no effect on the function and appearance. In most cases, the failure loads are multiples of the specified value.
  The details relating to the load bearing capacity are non-binding recommended values and rule out any liability. They constitute no general warranty of quality and condition.
  The user must determine from case to case whether a product is suitable for the intended use. Environmental influences and aging may influence these values.
  

  • Remise sur volume

  Fichiers CAD 2D / 3D disponibles

  à partir de∗ ：	9.62 €
  Délai d'expédition minimum ：	4 jours

  *Prix unitaire/configuration de base

• 

  Charnières d'angle amovible / filetage intérieur / zinc / GN 161.2 / GANTER

  GANTER

  Hinges GN 161.2 are a variant with highly attractive design. The fixing screws are invisible.
  During the load tests, the hinges were gradually loaded and relieved at room temperature with incrementally increasing force. For the specified values, an insignificant permanent deformation remained after relieving the load which had no effect on the function and appearance. In most cases, the failure loads are multiples of the specified value.
  The details relating to the load bearing capacity are non-binding recommended values and rule out any liability. They constitute no general warranty of quality and condition. The user must determine from case to case whether a product is suitable for the intended use. Environmental influences and aging may influence these values.

  • Remise sur volume

  Fichiers CAD 2D / 3D disponibles

  à partir de∗ ：	10.88 €
  Délai d'expédition minimum ：	5 jours

  *Prix unitaire/configuration de base

• 

  Charnières d'angle / bonlon / acier inoxydable / GN 129.5 / GANTER

  GANTER

  Stainless Steel-Hinges GN 129.5 are used for doors which are flush with the frame on the outside. Once assembled, they cannot be unhinged.
  With the fixing from the inside, they are especially suitable for doors and trap doors which must not be detachable from the outside as an anti-tamper device.

  • Remise sur volume

  Fichiers CAD 2D / 3D disponibles

  à partir de∗ ：	26.94 €
  Délai d'expédition minimum ：	5 jours

  *Prix unitaire/configuration de base

• 

  Charnières pour profilés en aluminium / éléments de surface, en trois parties

  GANTER

  • Remise sur volume

  à partir de∗ ：	28.96 €
  Délai d'expédition minimum ：	9 jours

  *Prix unitaire/configuration de base

• 

  Charnières de porte avec interrupteur de sécurité / filetage intérieur / acier inoxydable / GN 139.5, type CK / GANTER

  GANTER

  Hinges GN 139.5 with integrated safety switches have been designed for monitoring doors and covers of machines and plants. Opening the door will activate the switch contacts which, in turn, will then e.g. interrupt a protective circuit via break contact (NC) and at the same time signal the door opening by closing a normally open contact element (NO). The contact blocks are fitted with positive opening slow-action contacts, i.e. they will definitely be separated when activated and have no hysteresis. The angle at which the switching points are reached are adjustable.
  Together with the integrated contact blocks, the hinges are a compact, easy to mount unit with an attractive design. The mounting from the back make the hinge more tamper-proof. Hinges GN 139.6 without switching function act as additional hinges, e.g. for larger doors or gates where several hinges are required.

  • Remise sur volume

  Fichiers CAD 2D / 3D disponibles

  à partir de∗ ：	648.68 €
  Délai d'expédition minimum ：	5 jours

  *Prix unitaire/configuration de base

• 

  Charnières d'angle / Fiches à cylindre / acier / GN 129.3 / GANTER

  GANTER

  Hinges GN 129.3 are used for doors which are flush with the frame on the outside. Once assembled, they cannot be unhinged.
  By using cylinder screws DIN 912, they are conveniently fixed using threads on the user side or by using through screws for different clamping thicknesses.

  • Remise sur volume

  Fichiers CAD 2D / 3D disponibles

  à partir de∗ ：	23.36 €
  Délai d'expédition minimum ：	4 jours

  *Prix unitaire/configuration de base

• 

  Charnières / filetage intérieur / asymétrique / zinc moulé / GN 138 / GANTER

  GANTER

  With their attractive design, hinges GN 138 are suitable for use in plant and machinery where a well-designed and stylish appearance is important.
  The concealed and tamper-proof mounting from the rear highlights and enhances the special appearance of the hinge.
  The dimensions l1 / l2 and the drill hole spacings m1 / m2 match the usual hinges GN 237 / GN 237.1 and can replace these.
  

  • Remise sur volume

  Fichiers CAD 2D / 3D disponibles

  à partir de∗ ：	8.74 €
  Délai d'expédition minimum ：	4 jours

  *Prix unitaire/configuration de base

• 

  Charnières / à trous oblongs / asymétriques / zinc moulé / GN 161 / GANTER

  GANTER

  Hinges GN 161 have been designed for commercially available profile rails.
  With three different types of hinges only, 66 different groove distances „n“ can be accommodated. To achieve this the positioning elements are set in specially marked recesses in the hinge wings.
  The rectangular (8x10 mm) positioning elements, two pieces per hinge wing, will prevent a misalignment. They will also carry the weight of the door.
  For screwing the hinges onto the profile rails, special T-Nuts are used.

  • Remise sur volume

  Fichiers CAD 2D / 3D disponibles

  à partir de∗ ：	15.22 €
  Délai d'expédition minimum ：	Jour même

  *Prix unitaire/configuration de base

• 

  Charnières de porte / filetage intérieur / zinc moulé sous pression / GN 139.2, type AK,CK / GANTER

  GANTER

  Hinges GN 139.1 with integrated safety switches have been designed for monitoring doors and covers of machines and plants. Opening the door will activate the switch contacts which, in turn, will then e.g. interrupt a protective circuit via break contact (NC) and at the same time signal the door opening by closing a normally open contact element (NO).
  The contact blocks are fitted with positive opening slow-action contacts, i.e. they will definitely be separated when activated and have no hysteresis. The angle at which the switching points are reached are adjustable (see contact travel diagram).
  Together with the integrated contact blocks, the hinges are a compact, easy to mount unit with an attractive design. The mounting from the back make the hinge more tamper-proof.

  • Remise sur volume

  Fichiers CAD 2D / 3D disponibles

  à partir de∗ ：	165.90 €
  Délai d'expédition minimum ：	5 jours

  *Prix unitaire/configuration de base

• 

  Charnières / filetage intérieur / asymétrique / zinc moulé sous pression / GN 139.1 / GANTER

  GANTER

  Hinges GN 139.1 with integrated safety switches have been designed for monitoring doors and covers of machines and plants. Opening the door will activate the switch contacts which, in turn, will then e.g. interrupt a protective circuit via break contact (NC) and at the same time signal the door opening by closing a normally open contact element (NO).
  The contact blocks are fitted with positive opening slow-action contacts, i.e. they will definitely be separated when activated and have no hysteresis. The angle at which the switching points are reached are adjustable (see contact travel diagram).
  Together with the integrated contact blocks, the hinges are a compact, easy to mount unit with an attractive design. The mounting from the back make the hinge more tamper-proof.

  • Remise sur volume

  Fichiers CAD 2D / 3D disponibles

  à partir de∗ ：	168.64 €
  Délai d'expédition minimum ：	5 jours

  *Prix unitaire/configuration de base

• 

  Charnières de porte avec interrupteur de sécurité / filetage intérieur / acier inoxydable / GN 139.5, type A,B,C / GANTER

  GANTER

  Hinges GN 139.5 with integrated safety switches have been designed for monitoring doors and covers of machines and plants. Opening the door will activate the switch contacts which, in turn, will then e.g. interrupt a protective circuit via break contact (NC) and at the same time signal the door opening by closing a normally open contact element (NO). The contact blocks are fitted with positive opening slow-action contacts, i.e. they will definitely be separated when activated and have no hysteresis. The angle at which the switching points are reached are adjustable.
  Together with the integrated contact blocks, the hinges are a compact, easy to mount unit with an attractive design. The mounting from the back make the hinge more tamper-proof.

  • Remise sur volume

  Fichiers CAD 2D / 3D disponibles

  à partir de∗ ：	654.80 €
  Délai d'expédition minimum ：	5 jours

  *Prix unitaire/configuration de base

• 

  Charnières / réduction conique / zinc moulé sous pression / GN 238 / GANTER

  GANTER

  The adjustable hinges GN 238 allow the technically and visually perfect positioning and alignment of a door in its frame.
  The steel adjusting disc has a cutting ring in its underside which cuts into the radial fins of the zinc die-cast wings when the countersunk screw is tightened, virtually creating a form-lock that prevents adjusting the hinge after mounting.
  The covers conceal the fixing elements and lend the hinge an attractive optical appearance.

  • Remise sur volume

  Fichiers CAD 2D / 3D disponibles

  à partir de∗ ：	11.66 €
  Délai d'expédition minimum ：	Jour même

  *Prix unitaire/configuration de base

• 

  Charnières d'angle / bonlon / acier / GN 129.2 / GANTER

  GANTER

  Hinges GN 129.2 are used for doors which are flush with the frame on the outside. Once assembled, they cannot be unhinged.
  With the fixing from the inside, they are especially suitable for doors and trap doors which must not be detachable from the outside as an anti-tamper device.

  • Remise sur volume

  Fichiers CAD 2D / 3D disponibles

  à partir de∗ ：	16.98 €
  Délai d'expédition minimum ：	5 jours

  *Prix unitaire/configuration de base

• 

  Charnières de porte / filetage intérieur / zinc moulé sous pression / GN 139.2 / GANTER

  GANTER

  With the exception of the connector plug, hinges without safety switch GN 139.2 do not differ in their external appearance from hinges with safety switch GN 139.1. With the concealed screw connection at the back, the hinge is also tamper-proof.
  The compact design combines safety and attractive appearance.
  The design with broad hinge halves is intended for mounting to glass or polycarbonate doors.
  

  • Remise sur volume

  Fichiers CAD 2D / 3D disponibles

  à partir de∗ ：	41.76 €
  Délai d'expédition minimum ：	4 jours

  *Prix unitaire/configuration de base

• 

  Embases de charnières / Equerre / zinc moulé / 139.4-101 / GANTER

  GANTER

  The angled mounting plate GN 139.4 allows the hinges GN 139.1 / GN 139.2 to be attached between frame and door, i.e. the door gap.
  The long slotted holes allow the attachment to profile
  systems.
  Countersunk screws for fixing the hinges to the mounting plate are
  included part of the order.

  • Remise sur volume

  Fichiers CAD 2D / 3D disponibles

  à partir de∗ ：	25.04 €
  Délai d'expédition minimum ：	5 jours

  *Prix unitaire/configuration de base

• 

  Embases de charnières / trous oblongs / acier / Galvanisé / 139.3-170 / GANTER

  GANTER

  The flat mounting plate GN 139.3 allows the hinges GN 139.1 / GN 139.2 to be attached from the front.
  The long slotted holes allow the attachment to profile
  s ystems.
  Countersunk screws for fixing the hinges to the mounting plate are
  included part of the order.

  • Remise sur volume

  Fichiers CAD 2D / 3D disponibles

  à partir de∗ ：	35.96 €
  Délai d'expédition minimum ：	5 jours

  *Prix unitaire/configuration de base

• 

  Charnières de porte / filetage intérieur / acier inoxydable / 139.6-76-126 / GANTER

  GANTER

  With the exception of the connector plug, the hinge without safety switch GN 139.6 do not differ in their external appearance from hinges with safety switch GN 139.5. With the concealed screw connection at the back, the hinge is also tamper-proof.
  The compact design combines safety and attractive appearance.
  The design with broad hinge halves is intended for mounting to glass or polycarbonate doors.

  • Remise sur volume

  Fichiers CAD 2D / 3D disponibles

  à partir de∗ ：	498.10 €
  Délai d'expédition minimum ：	5 jours

  *Prix unitaire/configuration de base

• 

  Charnières d'angle / bonlon / acier inoxydable / GN 129.2 / GANTER

  GANTER

  Stainless Steel-Hinges GN 129.2 are used for doors which are flush with the frame on the outside. Once assembled, they cannot be unhinged.
  With the fixing from the inside, they are especially suitable for doors and trap doors which must not be detachable from the outside as an anti-tamper device.

  • Remise sur volume

  Fichiers CAD 2D / 3D disponibles

  à partir de∗ ：	32.70 €
  Délai d'expédition minimum ：	5 jours

  *Prix unitaire/configuration de base

• 

  Jeux de boulons, charnons GN

  GANTER

  • Remise sur volume

  à partir de∗ ：	2.96 €
  Délai d'expédition minimum ：	7 jours

  *Prix unitaire/configuration de base

• 

  Charnières pour profilés en aluminium / éléments de surface, en trois parties, étirées verticalement

  GANTER

  • Remise sur volume

  à partir de∗ ：	38.70 €
  Délai d'expédition minimum ：	9 jours

  *Prix unitaire/configuration de base

Loading...