SURUGA SEIKI Supports laser

?* À propos du délai d'expédition et des prix

• 

  Support LD

  SURUGA SEIKI

  F511L: fixed type. F512L, F513L: YZ axis adjustable LD holder. Select according to the number of pins and the pin pitch (pin P.C.D.) of the LD.

  Fichiers CAD 2D / 3D disponibles

  à partir de∗ ：	122.44 €
  Délai d'expédition minimum ：	10 jours

  *Prix unitaire/configuration de base

• 

  Supports LD (modèle de porte-puce)

  SURUGA SEIKI

  [Features]
  · A Chip Carrier type LD holder with a built-in Peltier element.
  · Features a built-in Peltier element, and a calibrated 10kΩ thermistor sensor.
  · The switching for the anode/cathode of the LD can be configured by replacing the jumper pins.
  · There are two types of Chip Carrier LD holder. Configure according to the mounting (output) direction of the LD.
  · For connectors, a D-sub9 pin female is used for driving the LD, and a D-sub9 pin male is used for the temperature controller.
  · The F129-1 water cooling adapter is also available.
  · Use a low temperature circulating water tank or similar to enable greater stabilization and for even lower temperatures.

  Fichiers CAD 2D / 3D disponibles

  à partir de∗ ：	665.13 €
  Délai d'expédition minimum ：	11 jours

  *Prix unitaire/configuration de base

• 

  Support LD (Modèle pour paquet)

  SURUGA SEIKI

  [Features]
  · A To-Package type LD holder with a built-in Peltier element.
  · Features a built-in Peltier element, and a calibrated 10kΩ thermistor sensor.
  · Supports LD sizes of ø5.6 (Pin PCD, 2.0) and ø9.0 (Pin PCD, 2.54) for three-pins and for four-pins respectively.
  · For common anodes and common cathodes, etc., configure by replacing the jumper pins.
  · For connectors, a D-sub9 pin female is used for driving the LD, and a D-sub9 pin male is used for the temperature controller.
  · The F129-1 water cooling adapter is also available.
  · Use a low temperature circulating water tank or similar to enable greater stabilization and for even lower temperatures.

  Fichiers CAD 2D / 3D disponibles

  à partir de∗ ：	665.13 €
  Délai d'expédition minimum ：	5 jours

  *Prix unitaire/configuration de base

• 

  Supports de capteur / laser

  SURUGA SEIKI

  [Features]
  · Can adjust the tilt angle of small sensors and laser pointers.
  · P.C.D.32 tapped holes are included on the holder surface. Uses these to mount various types of adapter plate.

  Fichiers CAD 2D / 3D disponibles

  à partir de∗ ：	142.67 €
  Délai d'expédition minimum ：	5 jours

  *Prix unitaire/configuration de base

• 

  Support à laser rond

  SURUGA SEIKI

  [Features]
  · F20 sandwiches the laser between three screws. The optical axis is adjusted by screwing in and out.
  · With F21, in addition to the function of F20, it is possible to adjust in the θy direction by operating the screw at the bottom of the holder.
  · Both F20 and F21 have two types, L=150 and 250, depending on the length of the laser.
  · The included standard rod has a diameter of ø20 and a length of 60, but both the rod diameter and length can be changed upon request.
  · The laser holding part can be fixed to positions at 50 mm intervals by removing the fixing screw from the bottom (only F20-150/250).
  · The F20 can be attached directly to the breadboard (A65) by removing the rod.

  Fichiers CAD 2D / 3D disponibles

  à partir de∗ ：	145.58 €
  Délai d'expédition minimum ：	5 jours

  *Prix unitaire/configuration de base

• 

  Adaptateur refroidi par eau

  SURUGA SEIKI

  [Features]
  · A water cooling adapter for F125/F126/F127 LD holders
  · Connect to water tanks which circulate water at low temperatures to enable superior temperature stability and low temperature control.
  · Connect using a 1/4 inch hose (hose not included)

  Fichiers CAD 2D / 3D disponibles

  à partir de∗ ：	112.86 €
  Délai d'expédition minimum ：	5 jours

  *Prix unitaire/configuration de base

Loading...